Peugeot 208 Key Replacement
It is best to leave the replacement of Peugeot keys for 208 to auto locksmiths that have the equipment and know-how. They will be able to create and program new keys faster than a dealership would and at a cheaper cost.
If your key fob stopped locking or unlocking your doors, it is likely due to a dead coin battery. There are also other reasons for the key to be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking or unlocking, and will not allow you to start the engine. If this is the case, you'll have to make use of the backup starting procedure that is detailed in the owner's manual of your vehicle.
Another reason why your 208 might not start is because the spark plugs are been worn down. The spark plugs are responsible to ignite the fuel that powers the engine. They only last for a certain amount of time. If they're not used enough and they fail, they'll eventually die.
There is a simple solution for this issue. The best solution is to check the voltage of your car battery using a multimeter. If the voltage falls below 11,5 volts then it's time to replace it. If the battery has corrosion it is essential to clean its contacts. This can be done by removing the rubber covers from the two terminals on the battery and then using a wirebrush to eliminate any corroded battery parts. Then, you should connect the cables to the positive and negative poles.
Water Damage
If your 208 doesn't start and the battery hasn't been replaced, you must look at the spark plugs. You might find that they are simply too dirty and don't spark. This can be easily corrected by cleaning the spark plugs in the workshop.
peugeot partner key fob programming are equipped with keys that are transponder-type and works with the car's ignition system. This ensures that only the right key is able to turn the engine. If the chip in the Peugeot key is damaged then it will not send the proper signal to the vehicle.
This is a common problem that can occur due to water damage. This is particularly common in colder climates, where the vehicle could have been exposed to rain or snow. In this instance, you should contact an experienced locksmith who will have the tools and equipment required to modify the key. They'll also have the latest technology and machinery required to create the Peugeot smart key. The process shouldn't take more than 15 minutes.
Contacts with the battery may be damaged.
Peugeot changed from the carbon-encased transponder chips to an entirely new kind of chip that utilizes electronic components on a circuit board. This new system works great when it's brand new, but over time the circuit boards begin to lose their effectiveness and cease working properly.
This could prevent the immobiliser from activating so your vehicle will not start. Contact a Peugeot specialist or a locksmith if this is the case.
A common issue is when the battery inside the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A locksmith from your car will replace the battery and then cut a new blade for you. This is a quick solution.
Faulty Receiver Module
If your Peugeot key fob has stopped working after dropping it on the floor, or being exposed to a sudden downpour or accidentally washing it the wrong way, it could be due a malfunctioning receiver module. The receiver is responsible for transmitting radio frequency signals to the onboard computer that controls the central locking system inside your Peugeot vehicle.
The key fob itself is fitted with rubber seals to prevent water from reaching the chip inside. However, prolonged exposure to water can cause damage to these seals and the chip. Submerging the key fob into sea water at the beach or throwing it into the pool can be especially damaging because of the high salt content.
If your Peugeot spare key fob stops working it is necessary to have the module replaced. This can only by done by a Peugeot specialist or a professional auto locksmith. In contrast to other vehicles, Peugeot keys are protected by a unique immobilizer system that requires the correct programming to start the engine. This is why you should only be able to trust a professional Peugeot locksmith to take on the job of designing and programming the replacement.
Computer on-board is not working properly
The on-board computer in your Peugeot is the one responsible for all of the systems within the car, from power windows to the airbags. The on-board computer will show the code when something goes wrong. This code is saved in the system and stays there until the issue has been resolved. This may require the on-board computers to be replaced.
One of the most common causes of the light turning on is loose or corroded connections in the airbag sensor. This can be caused by wear and tear, aging, or exposure to moisture and salt. This issue should be taken care of as soon as you can, as an airbag that's malfunctioning could pose a risk in the event of an accident.
If your Peugeot is showing a card not detected error, then the battery in the key fob could be dead or weak. This will prevent the key fob from sending a signal that disables the immobilizer on your vehicle's standard. You can test this by pressing the unlock button on the key fob, then attempting to start your car. If it doesn't work then the battery in the key fob is in need of replacement.